Herculiner

[Misfit8]

I'm goin to herciline the TJ again, that will give it 4 solid coats, no more carpet. Anyone have any good ideas for heat shieds up front.

[highlander]

I saw some stuff that adhears to the bottom of your tub, under the floorboard.... I didn't even think about it earlier when we were talking.. :bang:

Just cant think of the name of it

[Rockjock]

Carpet :flip:

[Misfit8]

I was thinkin about a piece of alum. daimond plate spaced 1/2 inch above the floor allows for an air gap.

[Rockjock]

Were you putting that in your jeep?

Try this to keep it out. http://www.heatshieldproducts.com/heat_shield.php
Just be carefull about using it to cover an entire firewall. Can make for a hot engine compartment. :thumb:

[Misfit8]

Passanger and drivers floor board right and left of the shifter.

[Rockjock]

This might be better. http://www.quietride.com/heat_sheild.html Also look at exhaust wraps.

[Rockjock]

I don't think I would like my floor an inch taller.

[highlander]

If your talking about your floor board there ya go!!!


Just rivit it in!!! :thumb:

[Misfit8]

The air gap should help 1/2 inch might work I'm goin to try it any way.

[Misfit8]

:thumb:

[highlander]

under the floorboard? Or over it?

[Misfit8]

Inside

[XTrmXJ]

aliminuim foil

[Misfit8]

1/8 diamond plate

[highlander]

if you go under and use some galvanized sheet you'd get double duty..

The plate would reflect most of the heat, and then the air movement through th space would cool!!!


]____________[

Just pop a couple of rivits on either side of the flanges!

[Rockjock]

Do you think the plate inside the jeep would give you some loud acusticles? I say keep the heat out. :mrgreen:

[Misfit8]

Good thought

[highlander]

Already worked on that for the sis in laws XJ. :thumb:

[Rockjock]

I have no carpet and no liner on the floor. I also cheap lined the inside of my hard top and my jeep keeps getting louder. :shock:

[highlander]

1 word....

Dynamat!!!

[XTrmXJ]

1/8 diamond plate

Really expensive

[Misfit8]

Check for holes :razz:

[XTrmXJ]

if you go under and use some galvanized sheet you'd get double duty..

The plate would reflect most of the heat, and then the air movement through th space would cool!!!


]____________[

Just pop a couple of rivits on either side of the flanges!


You would have to install one in the center and cross ways or it going to sound like thunder going down the road

[highlander]

Maybe one in the middle, but there's not that much wind to move it around much where I'm going to put it.

[XTrmXJ]

Maybe one in the middle, but there's not that much wind to move it around much where I'm going to put it.

Your doing it under the Jeep right ?

[Misfit8]

Ya know a rear engine jeep would cure the problem, Jon don't get any ideas.

[XTrmXJ]

Ya know a rear engine jeep would cure the problem, Jon don't get any ideas.

Already drawn up... Damit

[Misfit8]

Go figure...

[XTrmXJ]

What do expect. you should see my sketch book. its full of plans and idea, and sketches

[Misfit8]

Get a publisher :thumb:

[highlander]

Yep under the jeep, with the small gap and rounded forn to fit the tunnel I don't think it'd make too much noise....


Maybe I'll just have to wind test a piece at work tomorrow!! :twisted:

[XTrmXJ]

Ive thought of that but I would need to build it first.. Like building an extended XJ with a bed and a duely

[highlander]

*L* build then test...


Ancient redneck rule #72

[XTrmXJ]

Hay ya'll watch this, Hold my beer

[Misfit8]

:thumb:

[highlander]

Rule #1

If ya can't duck it........*LOL*

[XTrmXJ]

Duct tape

[highlander]

Oh nevermind the main cheap producer of duct tape is a company called DUCK TAPE!!! *LOL*

Only a true redneck god would know that one!!!!

[XTrmXJ]

I knew that along time ago

[Rockjock]

I think the plate would work fine under the Jeep and be quiet but in the jeep would a differant story. :wave: